QU15004 Flat Tab Spindle Lock Washer with Narrow Key Tab is a genuine New Old Stock (NOS) original equipment non-reusable Bend Over Tab Spindle Lock Washer that fits front and rear applications on 1950’s to mid 1970’s 3/4 ton, 1 ton, and 1-1/4 ton Dodge, International and Jeep trucks with 2″ spindle threads, narrow key slots, and regular hex spindle nut that measure either 2-1/2″ or 2-9/16″ across the flats. ID Key tab is approximately 3/16″ wide. Washer is about 0.088″ thick. USA Made. Very Limited Supply. Sold Individually. Order 2 per axle.

Need More Info? Use the handy Links below to access over 40 years of Dan’s product and vehicle specific Tech Notes to easily get the information you need for your vehicle’s repair, maintenance, or upgrade project!

Dan the Gear Man Tech Notes:
Tabs
Non-Reusable
Alternate Parts
Matching Parts for 1967-1969 Jeep M715 Dana 60 Front Axle
Matching Parts for 1967-69 Jeep M715 Rear

Tech Note 1: Tabs
Typically, one lockwasher tab is bent over a flat on the inner nut and either one or two are bent over flats on the outer nut.

Tech Note 2: Non-Reusable
Customer Statement: “Nonreusable? Dan what are you talking about? I always reuse them until all the tabs break off!” Well guys, for safety reasons, these lock washers must be discarded after every use. That means any time you bend up a tab to readjust or remove the spindle nuts. Why? Metal fatigue. The outer lock tabs lose some of their strength after they are straightened out. Also, the inside tab that fits in the spindle keyway has a tendency to shear when the outer nut is tightened against it more than one time. Reusing a bend over tab lockwasher may save you a few dollars, but by doing so you might kill yourself and others when you lose a hub and wheel going 75 mph down the Interstate. Don’t risk it!

Tech Note 3: Alternate Parts
For 2″ Diameter Spindles, the available Spindle Nut Lock Washers for Hex and Rounded Hex Nuts Are:
TK20017 3/16″ Wide Inside Key Tab. Washer Thickness is 0.0625″ (1/16″) Ford 1957-1979
QU15004 3/16″ Wide Inside Key Tab. Washer Thickness is 0.088″ Vintage Dodge, IHC, Jeep
QU40051 1/4″ Wide Inside Key Tab. Dodge, IHC

Tech Note 4: Matching Parts for 1967-1969 Jeep M715 Dana 60 Front Axle
QU15006 6 Bolt Axle Flange Gasket
QU40052 Spindle Lock Nut
QU15008 Spindle
QU90018 Pyroplex Synthetic Grease
QU90021 Spicer Ultra Premium Synthetic Grease
QT5500 Wheel Bearing Packer

Tech Note 5: Matching Parts for 1967-1969 Jeep M715 Rear Axles
QU50402 Timken Inner Wheel Bearing Cup
QU50568 Timken Outer Wheel Bearing Cup
QU50569 Timken Outer Wheel Bearing
QU50717 Rear Wheel Seal
QU40052 Spindle Lock Nut
TK8338 Premium Rear Wheel Bearing Kit with Tools
TK8339 Premium Rear Wheel Bearing Kit without Tools
QU15003 8 Bolt Rear Axle Shaft Flange Gasket
QU40577 Locking Bushing Cone for Rear Axle Shaft
QU50403 Timken Taper Bearing
QU90018 Pyroplex Synthetic Grease
QU90021 Spicer Ultra Premium Synthetic Grease
QT5500 Wheel Bearing Packer (Does not work with Inner Bearing)

Applications:
Jeep:
M715, M725, M726 military trucks with Dana 60 front axles: 1967, 1968, 1969
FC-170 trucks with Dana 70 dual rear wheel axles: 1957, 1958, 1959, 1960, 1961, 1962, 1963, 1964, 1965, 1966, 1967
J-Series Gladiator 1 ton trucks with Dana 70 dual rear wheel axles: 1962, 1963, 1964, 1965, 1966, 1967, 1968, 1969, 1970
1-1/4 ton military M715-M725 series 4x4s with Dana 70 single rear wheel axles: 1967, 1968, 1969